|Published (Last):||11 September 2006|
|PDF File Size:||17.80 Mb|
|ePub File Size:||10.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
Which repair manual is best to buy? Apply liquid gasket to the 1. Power is not transmitted to the secondary drive gear. Remove the 1st clutch and mainshaft 1st gear assem Slip the special tool onto the mainshaft as shown.
Remove the ATF passage line assembly one bolt. Attach the chain hoist to the engine. ChGck tor an opon in lho wite 3.
The 3rd, 4th, and sth gears are installed with a press. Gountershaft Assembly Index The 4th and sth gears maunal installed with a press. Transmission Reassembly cont’d The 2004 honda crv repair manual pdf download Sensor is a temperature dependant resistor thermistor. The line pressure 1 is regulated charged into 1. As illustrated below, use a commerciallv available Working from the camshaft side, use the driver and air-impact valve guide driver attachment modified an air hammer to drive the guide about 2 mm 0.
Remove the final driven gear from the differential lf the bearings are OK, removal is not necessary. Use new gaskets and self-locking nuts when reassembling. Countershaft Assembly Reassembly cont’d 4. Description The automatic transmission is a 3-element torque converter and a dual-shaft electronically controlled unit which provides 4 soeeds forward and 1 reverse.
Recommendations re CRV Repair Book or Manual? – Page 3
Check that the crankshaft pulley and camshaft pul- Install the timing belt tightly in the sequence shown’ ley are both at TDC. While replacing the speed sensor, be sure not to allow dust and other foreign parliclos to enter into the trans- mission.
Page Engine Lubrication “‘. Mainshaft AssemblY lndex Note the follow.
Transmission Assembly Installation Removal cont’d Install the transmission assembly in the reverse order of 1 7. Beforo iesting, be sure the transmission fluid is tilled to tho proper level’. Remove the vacuum hose from the fitting on the intake air duct, and connect a vacuum gauge to the nose.
Honda CRV Service Repair Manual | 01
General Information Ghassis and Paint Codes Originally Posted by illegal. Page Removal Loosen the idler pulley bracket bolt and adjusting Engine removal is not required for this procedure. Slide new cushion rings onto the fuel injectors.
When reassembling the primary rocker arm, care- head and inspect it.
Verity that the outside diameter ol the snap ring is reverse brake end plate and measure its thickness. Remove the snap ring. Mark the direction of rotation on the belt before 2004 honda crv repair manual pdf download.
Description Park Mechanism The park mechanism locks 2040 transmission by engaging the park pawl with the park gear which is integral with the sec- ondary drive gear’ The secondary drive gear engages with the secondary driven gear which engages wit-h the final driven gear.
Gamshafts Inspection cont’dl lf the camshaft-to-holder oil clearance is out of tol- Check the cam lobe height.
Special Tools SpecialTools Ref. Check the ball bearings for wear and rough rota- steps, and remove the final driven gear from the dif- tion.
2004 Honda Cr-v Crv Owners Manual.pdf
Page Rocker Arms lnstallation 4. Cleanall parts thoroughly in solvent or carburetor cleaner, and drywith compressed air. By Scott Schillereff in forum Maintenance and Service. Check clearance with plastigage see pagethen Use liquid gasket, part No. Turn the ignition switch ON lland make sure that voltage is Wire side ol female terminals available for two 2004 honda crv repair manual pdf download.
Make sure iacks and safoty xrv are downloae plop- erly 3ee section l. Change Holder Assembly Clearance Inspection cont’d Measure the clearance between the select arm and 9.
Disconnect the heated oxygen sensor HO2S con- 9. Originally Posted by “G”.
Do not overtighten the drain bolt. Remove the brake booster vacuum hose, fuel return hose and vacuum hose see page 5 4. Turn the ignition switch OFF.