|Country:||Trinidad & Tobago|
|Published (Last):||5 February 2005|
|PDF File Size:||4.26 Mb|
|ePub File Size:||17.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
To perform the fuel system test a scan tool is necessary to access the different test modes.
Sparks should always be avoided when working around batteries, especially when attaching jumper cables. Install new retainer clips in each push connect fitting. Connect the wiper motor’s wiring connector. Installation is the reverse 1997 ford explorer service manual pdf download removal.
Disconnect the driveshaft from the front axle yoke. Subscription is subject to compatible 4G network availability. Do sercice damage the sensing element or possible failure of the sensor may occur. Start the engine and check for leaks. If the alternator does not produce voltage within this range there is a problem in the charging system. Remove the camshaft by carefully withdrawing toward the front of the engine. Tighten the ring until secure. Remove the output shaft yoke washer, rubber seal and the yoke from the output shaft.
For OHV downloac also include a new camshaft and lifters. Running the system for five minutes each month no matter what the season 1997 ford explorer service manual pdf download help ensure that the seals and all internal components remain lubricated. A putty knife is a good tool to use for this.
Identification There are 5 automatic transmissions used in the Ford Ranger, Explorer and Mountaineer. If equipped, remove the skid plate from the frame. If you haven’t already, apply a generous amount of penetrating oil or solvent to any rusted fasteners. If these acids are allowed to concentrate, they can cause corrosion and rapid wear of the internal engine parts. Oil pan installation on the 4.
Place the timing chain tensioner in the retracted position and install the retaining clip. Failure to do this could result in the wheel coming off while the vehicle is in motion possibly causing loss of vehicle control or collision. The camshaft retaining bolt has a drilled oil passage for timing chain assembly lubrication.
For premium starter motor function, the resistance in the starting system must be kept to an absolute minimum. About 50 percent of the measured torque is used in overcoming bearing friction. Position a piece of wood on a floor jack and raise the engine carefully as far as it will go. Be sure to check the level only when the car is sitting level. Tighten the retaining bolts to specifications. Open the ash tray and remove the two retaining screws. If necessary, open the bulb access panel by depressing the latch then lifting.
Pull the line from the connector. Remember that some longer exhaust pipes may be difficult to wrestle 1997 ford explorer service manual pdf download from under the vehicle if it is not supported high enough. It also adjusts ignition spark timing to provide the best balance between driveability and economy, and controls the IAC valve to maintain the proper idle speed. The questions most mechanics attempt to answer first, “is there spark?
Obtain a 1997 ford explorer service manual pdf download gasket for the intake assembly before removing it. No drag must 1997 ford explorer service manual pdf download present on the axle. The heated sensors are located before and after the dual converters in the exhaust pipes.
At the extreme ends of lever travel, the door should be heard to firmly seat, indicated by a loud thumping sound, allowing either maximum or no air flow through the heater core. The processor substitutes a fixed value for the missing sensor signal.
Owner Manuals | 01
Connect the blower motor cooling tube. If the battery were shorted to ground, the alternator would also be shorted. If not already attached, connect the sending unit.
Remove the jackshaft sprocket and chain assembly.
Any bent or twisted connecting rods must be replaced. A small magnet may help in removing the locks. Remove the fuel filter mounting bracket pf nuts. All breakers will automatically reset if they have been tripped. A metal electrode extends downward through the center of the insulator and protrudes a small distance. Remove the regulator, with 1997 ford explorer service manual pdf download brush and terminal holder attached.
Install the left linkage on the wiper motor crank pin.
Use new cylinder head bolts. Loosen the wheel lug nuts then raise and safely support the front of the vehicle.