|Published (Last):||23 September 2015|
|PDF File Size:||4.99 Mb|
|ePub File Size:||12.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 70 Warning Lights and Gauges Turn off the engine. Tighten the retaining bolts to specifications. Install the transmission following the procedure diwnload Section 7. Driving Your Ranger Secure all items in cargo area to 1996 ford ranger repair manual pdf download them from falling out and creating a downlooad hazard on the roadway.
Have the headlight adjustment checked as soon as possible by a reputable repair shop. Be sure to check the level only when the car is sitting level.
Using feeler gauges, determine the clearance at the center of the straightedge and across the cylinder head at several points. When installing the new gasket, the flange faces the sensor and the words “panside” should face nanual oil pan.
Brake Fluid If the fluid is low, carefully clean and remove the cap from the reservoir. For 4×4 vehicles, engage 1996 ford ranger repair manual pdf download, and try to drive slowly away. Page Using the Power Windows If equipped Each door has a power control that opens and closes the window on that door. Page Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal.
Dowwnload the cluster lens and install the cluster into the instrument 1996 ford ranger repair manual pdf download. Follow the warning above. Remove the lower manifold and its gasket from the engine. Stand away from the radiator opening. For heavier trailer applications, refer to the towing information found later in this chapter.
Silicone sealer and intake end seal application for the 3. The use of premium grades may actually cause driveability problems. Page If the power steering fluid is low, do not drive your vehicle for a dowmload period of time before adding fluid.
Disconnect the vehicle wiring harness connector from the distributor. Page Use this chart to perform your calculations.
Towing the Vehicle Ford recommends that a flat bed tow service be donload. Add grease to the hub until the grease is flush with the inside diameter of the bearing cup. Look the canister over and replace it with a new one if there is any evidence of cracks or other damage.
Ford Ranger Owner’s Manual
The fastener is then tightened the specified additional portion of a turn measured in degrees. Please refer to the chapter titled Servicing Your Ranger in this Owner Guide for instructions on checking and replacing fuses. Check for ranyer leaks and if found, repair the leaks before continuing. If equipped, remove the engine damper mounting bracket from the engine.
Bring the vehicle back to idle. Position a piece of wood on a floor jack and raise the engine carefully as far as it will go. A special tool is available from Ford and other manufacturers for removing the retaining clips.
If necessary, unbolt the chain guide attaching bolts If necessary, at this time the ICM can be removed from the heat sink.
Remove the RH camshaft sprocket and fasten a rubber band around the chain and the cassette to prevent the chain from dropping into the engine Hold the chain to the cassette with a rubber band to aid removal and prevent the chain from falling into the cylinder block. Drain the cooling system. On 1996 ford ranger repair manual pdf download transmission vehicles a removable consolette is located on the floor.
Page 5 This guide describes equipment and gives specifications for equipment that was in effect when 1996 ford ranger repair manual pdf download guide was approved for printing. Position head gasket on the block. Install the camshaft sprocket bolt doqnload washer. Slide the white plastic sleeve toward the slave cylinder while applying a slight tug on the tube. Extended operation in 4WD with a temporary spare may result in damage to powertrain components.
Ford Ranger Owners Manual PDF
The Motorcraft maintenance-free battery does not require additional water during its life of service. Check the fluid level on the dipstick which is highlighted in yellow in your vehicle.
Index Crankcase emission filter When you are sure that all the pressure has been released, use the cloth to turn and remove cap. This is the friction between the bearing surface of the bolt head, screw head or nut face and the base material or washer the surface on which the fastener is rotating.